Alle LUN nicht angezeigt im vSphere Client (ESXi)

Hallo,

habe 2x Open-E Server mit:
Modell: Data Storage Software V6
Version: 6.0up80.8101.5605 32bit
Lizenzierte Kapazität: 4 TB

davor kommen 2x ESXi mit v 4.1

Die beiden Open-E Server sind mit iSCSI Failover konfiguriert,
mit 1x Volumegruppe und 2x Volumes a)1900GB b)800GB.
Habe 1x iSCSI Target für das Failover der beide Volumes mit LUN 1 und LUN 2 zugeordnet hat. Bis hierher gibt es keine Probleme und das Failover läuft ohne Probleme.

Den ESXi Software iSCSI Software Adapter habe ich IP, iSCSI-Name und dynamische Erkennung (virtuelle IP vom Failover) konfiguriert.

Lasse ich nun nach Geräten suchen bekomme ich nur die LUN 1 mit 1,86TB angezeigt.
Das gleiche auf dem 2. ESXi Host. Habe die Volumes

Ist das Problem bei den Open-E Servern oder haben die ESXi da ein Problem?

Habe noch ein weiteres System mit fast gleicher Ausstattung (2x Open-E + Failover), dort ist nur ein Volume (850GB) mit der LUN 0 an 2x ESXi Server gebunden und da gibt es keine Probleme (seit über 1 Jahr im Einsatz).

Hello, Welcome you to the Open-E forum, we post here in english so most of the visitors can read it, I tried to translate your post with a web translator, and I'm sorry but i did not get you clear, is there only one volume from two? or a system can see both and the other no !

===translated copy using web translator====

Hello,

have 2x Open-E server with:
Model: Data Storage Software V6
Version: 32bit 6.0up80.8101.5605
Licensed capacity: 4 TB

before 2x ESXi come with V 4.1

The two Open-E iSCSI servers are configured with failover
with 1x volume and 2x volume group a) 1900GB b) 800GB.
I was assigned to 1x iSCSI target for the failover of both volumes with LUN 1 and LUN second Thus far there are no problems and that failover is running without problems.

Your ESXi Software iSCSI software adapter I IP, iSCSI name recognition and dynamic (virtual IP address from the failover) configuration.

I leave now search for devices, I only get the one with 1.86 TB LUN displayed.
The same on the second ESXi host. Have the volumes

Is the problem with Open-E have the ESXi servers or as a problem?

I still have another system with almost the same features (2x Open-E + failover), there is only one volume (850GB) with the bound LUN 0 to 2x ESXi server and there are no problems (since about 1 year now).

Hallo,

on Open-e are 2 volumes on one iscsi target with lun 1 and 2. (1.9TB & 0.8TB)
Both esxi servers can only see one of the volumes, lun 1.

Try to close your ISCSI session, and reconnect it. Also check the settings/configurations in your initiator, even if you have to remove this settings/configuration and create them again.

The following post may help you :
http://forum.open-e.com/showthread.php?t=1550

Hallo,

i have identified a network problem (nic interfaces assignment is wrong on one servers, no idea how it was incurred). I make a new configuration on open-e settings and give a feedback again.

Nice weekend

Network is fine.

Situation:

Open-E (replication,failover working) with two volumes, vol00=100GB and vol01=50GB (all for testing)

Szenario A
failover-target1 - vol00 + iSCSI ID + LUN 0 (100GB)
failover-target2 - vol01 + iSCSI ID + LUN 1 (50GB)

esxi only show a LUN 0 with 50GB
(open-e has the vol01+LUN 1 the 50GB) :eek:

Szenario B
failover-target1 - vol00 + iSCSI ID + LUN 0 (100GB) & - vol01 + iSCSI ID + LUN 1 (50GB)

esxi only show a LUN 0 with 100GB :confused:

I have tested the failover-target1 with vol00+LUN1 and vol01+LUN2, esxi shows here only a LUN1 (vol00,100GB)

Now i have the failover deactivated on one open-e server (no1) and only the volumes on the iscsi target configured.

Open-e Server:
bond0 with IP 192.168.2.220
failover-target1 + vol00(LUN0) + vol01(LUN1) + vol02(LUN2)

on exsi (with vmkernel network 192.168.2.200) i see all LUNs (0,1,2)

Only in failover with virtual IP are the LUNs not working/not to see.