The 'default disk timeout' which is that if a disk is not responding or is in a search-loop or whatever is 7 sec. by default. You can configure this in your RAID controller. When the disk gives...
Type: Posts; User: Roeller
The 'default disk timeout' which is that if a disk is not responding or is in a search-loop or whatever is 7 sec. by default. You can configure this in your RAID controller. When the disk gives...
Hello,
I would like to install a new Open-E system with some Intel 520 Series SSDs on an Areca 1680 or 1880 controller.
When the system fills up,.. and deletes again... and fills up... the SSDs...
I've seen this many times and I'm always praying on my knees when it reaches a few critical stages... 59% is one of them.
I've seen it taken about 10 or 15 minutes at 59%.
1) Might be a scan...
Thanks for the info Todd,
I'm trying to remember the situation:
- Customer was using version 6.0up95.xxxx.6156 (2012-04-05)
- The Primary was master and the Secondary was slave.
- The secondary...
Hello,
I have a FAILOVER/iSCSI configuration running with 2 XenServers for a customer.
I noticed a few times that when the Secondary Unit reboots, crashes or when I uncable it... There is NO more...
I had a crashed Open-E failover cluster, the systems wouldn't boot beyond the 90% anymore unless I disconnected all the network cables OR booted in 32-bit mode (but then the volumes were not...
After some hours,. I finally found the issue.
The maximum password length for 'Data(file) replication' in Open-E is only 8 characters.
I was pasting the password which had more that 8 characters....
Hello,
A customer of me has a DSSv6 and wants to export his shares on a weekly basis to a Synology Disk Station.
On the Synology Disk station you can enable the Rsync deamon.
When I test from...
I opened a support ticket.
The unit is 'remote support connected' now. Under ticket: 1026005.
-Roel
Most people use the Auto Update from the webinterface. I assume it does the MD5 check itself.. ?
It must be a bug in the software... more people have this issue.
I tried IE8 and IE9, both in 'normal' and in Compatibility mode.
I did CTRL-SHIFT-DEL to clear all cache, etc.
(and note that I saw the same, which is a black screen, using Firefox).
After...
I just wanted to upgrade a SAN of one of my customers.
Downloaded the update... did the reboote.... couldn't get a webinterface anymore!
I tried on IE and on Firefox.
I even generated a new...
Hello,
Last week I spoke to Janus (at the Open-E training in Houten - The Netherlands).
He said there was an update for the problem of rebooting your Active Directory (AD) and losing the...
I've had the same problem with a Supermicro mainboard recently. After upgrading the BIOS, the problem was fixed.
Hello,
I have a problem; I need to give access to a Windows 2008 Server using the machinename, not a username.
Maybe you think it sounds stupid?
Read this:...
Robotbeat,
I understand wht you're saying. But i am not talking about NAS data replication.
I have seen a lot of storage platforms, my point of view is that the basics of Open-E ar good (Linux,...
http://www.roelbroersma.nl/media/images/linked/open-e-dss6-volume-replicaiton-problem.png
BTW. Why can't you change/edit your message on this forum in case you made a typo ? :confused:
We recently bought 2 DSS V6 Servers to use with XenServer.
We also bought 1 DSS V6 server which we wanted to use as a Replication Destination.
...
If you have a password (code) on you Areca raid card, after step5 type: "set password=xxxx" (replace xxxx with your password/code).
Hello,
I would like to share the following with you;
I have an Areca 1220 RAID Card and was not able to update the firmware using the Areca Webinterface.
1) Open a webbrowser and add a share...
Hello,
I have a machine with OPEN-E DSS V6 on it. It has 4x 10Gbit NICs.
I also have 2 Xenservers connected to it (with crossover cables).
The Open-E machine and the 2 XenServers are also...
I am also very curious how that works. I am looking at this for a few days now.
I found this document: http://support.citrix.com/article/CTX118791 (see: Basic Multipath Configuration).
In...