Is LSI MegaRAID Management still on last LAN port?

[silicon]

After another v6 Demo test, RWC access is definitely still on the last eth port only. That logon issue I note in the previous post didn't repeat (RWC often does that sort of thing, makes life confusing!), this time it found nothing at all. Cheers.

[To-M]

Just tested with V6 build 3534 (though I think you are using the latest if you just downloaded it) and the SSR212MC2 and go the following. I did this with Firefox but IE should be the same.


BatteryType iBBU
Voltage 5470 mV
Current 350 mA
Temperature 31 C
Firmware Status 00000028
Fully Discharged No
Fully Charged No
Discharging No
Initialized Yes
Remaining Time Alarm No
Remaining Capacity Alarm No
Discharge Terminated No
Over Temperature No
Charging Terminated No
Over Charged No
Relative State of Charge 40 %
Charger System State 4113
Charger System Ctrl 13
Charging current 350 mA
Absolute state of charge 38 %
Max Error 25 %
Relative State of Charge 40 %
Absolute State of charge 38 %
Remaining Capacity 335 mAh
Full Charge Capacity 831 mAh
Run time to empty 65535 Min
Average time to empty 65535 Min
Average Time to full 86 Min
Cycle Count 12
Max Error 25 %
Remaining Capacity Alarm 100 mAh
Remaining Time Alarm 10 Min
Auto Learn Period 2592000 Sec
Next Learn time 0 Sec
Learn Delay Interval 0 Hours
Auto-Learn Mode Enabled
Date of Manufacture 08/14, 2006
Design Capacity 880 mAh
Design Voltage 4800 mV
Specification Info 33
Serial Number 447
Pack Stat Configuration 0x68a0
Manufacture Name lsia11000a
Device Name *5806-4
Device Chemistry NiMH
IPMI Sensors:
BB +1.2V Vtt 1.2 V
BB +1.5V AUX 1.49 V
BB +1.5V 1.48 V
BB +1.8V 1.8 V
BB +3.3V 3.37 V
BB +3.3V STB 3.3 V
BB +1.5V ESB 1.49 V
BB +5V 5.1 V
BB +12V AUX 12.03 V
BB 0.9V 0.9 V
Baseboard Temp 33 °C / 91.4 °F
Mem Therm Margin 0 °C / 32 °F
P1 Therm Margin -45 °C / -49 °F
Proc 1 Vcc 1.22 V

[To-M]

After another v6 Demo test, RWC access is definitely still on the last eth port only. That logon issue I note in the previous post didn't repeat (RWC often does that sort of thing, makes life confusing!), this time it found nothing at all. Cheers.

I talked with engineers on found out that we have support for this for the LSI 8888 ELP, I am asking them to please fix this and note it in the release notes as well.

I heard from someone the Java version will work but RWC has or uses the JRE. So trying to figure that out. Sorry for the bump on this one but trying to get our guys to work on this ASAP.

[silicon]

Thanks for the update.
After yet another v6 install (3530), the hardware monitoring is working better, but I am sure there is still work to do. Eg. it is not reporting any Disk Status data at the moment (the MC2 uses the Intel SRCSASJV / LSI8888ELP card). In previous versions of DSS it would simply report them as all "empty", I think because the agent expected a SRCSAS144e card and not the SRCSASJV! I also think that if the agent doesn't like the hardware sensor data, it can make DSS GUI unstable. I will try yet again with latest version soon - but maybe it is not really ready for production yet. Cheers.

[To-M]

When you are done can you send the logs to support and this post link so the engineers can dig into it. Also latest is 3535.

[silicon]

Done, with latest version.
Just before grabbing the logs, I also repeated the test of pulling: a PSU (there are two), a fan, and a Hdd in RAID set. The server status LED lit yellow and enclosure / RAID card sounded alarms correctly, then restorded to normal, but no events appear to be logged. There's also a screenshot of the HW Monitoring page, eternally waiting for something.

I will repeat this exercise with v5 (eg. 3518) to compare soon, as we have a system ready to ship to a customer now, and v6 would not be a good idea yet.
Cheers.

[To-M]

Thanks for the logs we got them - please provide the update to the engineers so they can get this back to you. I need them to test this and look at the scripts.

[silicon]

Another test round using 3518 in 64bit mode (& this time started everything from scratch - no existing vg or config/setup), and replicated the last-port issue, & logs sent to support@open-e.com.
Summary:
- RWC detected MegaRaid agent/device on eth0 & eth1 ok, but login fails on eth1
- Raid vd degradation status changes were correctly logged and notifications sent this time

All in all, a good result considering the previous confusing results, hopping betwewn versions 3278, 3518, & v6updt4, and trying both 32 & 64 bit versions of each. Cheers.

[To-M]

Thanks for the tests Silicon, what was the ticket # that you received.

[silicon]

Not sure of the case number sorry, I generally just shift-delete all notifications! (but I do save all the replies).
The title of my email was: "Forum issue re MegaRaid & RWC - logon failure on all bust last eth port. For To-M", hopefully you can search on this. Cheers.