User / Gruppen anlegen nicht möglich

[To-M]

Are you using the Internal LDAP part of our setup for users and are you still not able to connect using the previous tests?

[Haeby]

Yes i use the Internal LDAP.

Her some Attitudes:

Server name: NAS-XSR
Comment: NAS

Authentication method
Workgroup (internal LDAP) --> i did not change

Workgroup: Haeby-Net

Use NFS
Use FTP (Port 21)

SMB Settings = Simple and protected negotiation

IP address = use dhcp


E-mail notification:
Send errors
Send test message
E-mail server: open-e.com --> i did not change

SSL Certificate Authority = donload and installed


Unit Manager:
Unit MD0 298.10 in use

Disks Localizer:
Unit S0
Unit S1

Antivirus setup:
Use antivirus
Use quarantine
Select share: Quarantine

Update virus definitions: Last update 2006.11.22

STATUS

IP address info:
Use dhcp: dhcp on
IP: 192.168.1.30
Netmask: 255.255.255.0
Broadcast: 192.168.1.255
Gateway: 192.168.1.1
DNS 0: 192.168.1.1

HARDWARE

Controllers info
Network controllers
Broadcom Corporation NetXtreme BCM5788 Gigabit Ethernet (rev 03)
IDE controllers
VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])

Drivers info
Network drivers:
Broadcom Tigon3 ethernet driver
IDE drivers:
"build-in"

S.M.A.R.T. info

Unit S0
Device Model: SAMSUNG SP1614C
Serial Number: 0888J1FX503065
Firmware Version: SW100-27
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0

HEALTH STATUS: PASSED


Unit S1
Device Model: SAMSUNG SP1614C
Serial Number: 0888J1FX510771
Firmware Version: SW100-27
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0

HEALTH STATUS: PASSED


RAID

RAID LEVEL RAID0
Creation Time Thu Nov 23 00:03:51 2006
Update Time Thu Nov 23 00:03:51 2006
Array Size 298.10 GB
Chunk Size 64K
State clean




Thanks

[Haeby]

so besides, it is possibly to access the console of the Nas-xsr by remote (telnet or ssh)? It is every time difficulty to connect the monitor to the Nas-xsr. ;-)

Thank you for your help

Andy

[Haeby]

In the meantime I have adjusted the language in English, removed the DVD drive still attached, started this one Nas repeatedly newly and tried again to create a user. It was the same result. I have copied a couple of files on a Share and, once more, while the files are still copied, I have tried to create a user again. And see there, the user, I had this one tried approx an hour before it became to lay out listed. Now the Function is ok, But I do not know the solution. ????

Andy

[To-M]

You can connect to the server by SSH connection using default port 22222. Please refer to the manual on how to achieve this. If you still are not able to add users please send logs to support@open-e.com

[Haeby]

I have got an answer of your support team today. There was a problem with LDAP server. I must change for a moment to ADS or PDC and then back to LDAP. That was the Solution. Now i can create user an groups.

Thank you for the good and fast support from her and from your support-team.

Andy

[To-M]

Thank you for the kind words.

[hesinka]

Is it good to open the console of the Nas-xsr by ssh remote? Thank for answering sir.

[To-M]

Yes and you should enable the Remote Console scree from the GUI and use Putty. See KB below.
http://kb.open-e.com/How-do-I-connec...motely_97.html